Featured Articles

Analysts expect ARM to do well next year

Analysts expect ARM to do well next year

British chip designer ARM could cash in on the mobile industry's rush to transition to 64-bit operating systems and hardware.

More...
Huawei and Xiaomi outpace Lenovo, LG in smartphone market

Huawei and Xiaomi outpace Lenovo, LG in smartphone market

Samsung has lost smartphone market share, ending the quarter on a low note and Xiaomi appears to be the big winner.

More...
Intel Broadwell 15W coming to CES

Intel Broadwell 15W coming to CES

It looks like Intel will be showing off its 14nm processors, codenames Broadwell, in a couple of weeks at CES 2015.

More...
Gainward GTX 980 Phantom reviewed

Gainward GTX 980 Phantom reviewed

Today we’ll be taking a closer look at the recently introduced Gainward GTX 980 4GB with the company’s trademark Phantom cooler.

More...
Zotac ZBOX Sphere OI520 barebones vs Sphere Plus review

Zotac ZBOX Sphere OI520 barebones vs Sphere Plus review

Zotac has been in the nettop and mini-PC space for more than four years now and it has managed to carve…

More...
Frontpage Slideshow | Copyright © 2006-2010 orks, a business unit of Nuevvo Webware Ltd.
Tuesday, 24 July 2012 12:40

Akasa integral S external 3.5" HDD case with USB 3.0 tested - Testing and results

Written by Sanjin Rados

integral s thumb

Review: Sleek and tough

 

Mounting a 3.5'' drive in integral S isn't hard. First thing we need to do is take off the I/O panel, which is held by two screws. Note that you shouldn't apply too much pressure when putting the screws back in, in order not to damage the threads.

integral-instal-1

The I/O panel acts as a bracket for drives and it must be taken out and strapped with a drive of choice. Note that although the enclosure isn't made for 2.5'' drives, users could still use it if they improvised. 

integral-s-drive-in-1

Setting the drive up was a breeze - SATA and power connectors were ready so all we had to do was put it back inside. Akasa opted for PL2771 SuperSpeed USB 3.0 to SATA II Bridge Controller.

integral-s-drive-in-3

For our testing, we used a brand new WD Red HDD 3TB drive.

integral-s-drive-in-2

When putting the bracket back in, you should watch out for LED cabling.

integral-s-drive-3

You'll have to reconnect the LED cable before sliding the drive fully into place.

integral-s-drive-4

The power cable is about 180cm long. The adapter isn't large and it will be easy to carry around, as opposed to the older integral P2SATA adapter. The picture on the left shows integral P2SATA's adapter, while the right one shows integral S'.

integral-power-cable

Once the disk is on, the logo glows blue.

logo1

Once the HDD is doing something, you should see it from the changes in logo lighting. However, it's impossible to tell exactly, even in complete darkness, because we're talking about very slight changes. Once we thought about it, it's probably god that the light isn't very obvious, because it would probably constantly draw attention to itself. It would be good if there was a smaller HDD indicator lamp on the I/O panel though.

The aluminum case is pretty scratch resistant. A clear proof of that is our old integral P2SATA case, picture below, which barely has visible scratches after few years of carrying around.

integral-sata-1

Users may have to watch the rubber feet though because although they're glued well, they may come off when tumbling around in a bag. After a few years of use, we have no idea where our Integral P2SATA's feet were lost. Perhaps it would be good if Akasa shipped a few spares in the box.

One of the cool things with integral cases is that they're stackable. The rubber feet fit into holes on top, which makes a nice and vibration free stack.

 

integral-stack-0

Integral S is only slightly longer than the integral P2SATA case. We noticed this when we tried to stack our integral P2SATA - it was possible, but not exactly a perfect fit.

 

integral-stack-1

Problems with dust and fingerprints cannot be avoided with piano black aluminum surface. Good thing is that it can be cleaned easily.

The stand is stable and also comes with rubber feet. We weren't particularly impressed with the stand, but it does what it does well.

 

integral-s-drzac-2

The stand is quite stable and the case is easily removed and put back.

integral-s-drzac-0

We put a fresh, formatted WD Red 3TB drive into the Integral S enclosure and got to work right away. USB 3.0 theoretically offers ten times faster transfer speeds than USB 2.0 but our testing showed only a 4x increase. Of course, this largely depends on the kind of drive you use and it's probably SSD drives that will show the real speed increase of USB 3.0. Atto Disk Benchmark shows that USB 3.0 connection in this case was 4x faster than USB 2.0-.

atto 2 in integral s usb2.0
USB 2.0 score

atto in integral s usb3
USB 3.0 score

Atto says performance is slightly better once our WD Red 3TB HDD is in the PC and connected to a SATA 6G controller. Note that performance is much better in the first part of our testing with smaller files, whereas working with larger files ran about the same.

atto in pc 1
SATA 6GB

(Page 4 of 5)
Last modified on Tuesday, 24 July 2012 12:55
blog comments powered by Disqus

 

Facebook activity

Latest Commented Articles

Recent Comments